Home PDF Bitmap Wood Model Airplane Plans (1) PDF Bitmap Wood Model Airplane Plans (2) Gym Dandy

Gym Dandy ( 37 in. / 94 cm )


Plan listing thumbnail Prev Next Plan
This is the Gym Dandy listing page, here you can download the plan, article and see the main thumbnail and extra images.

Gym Dandy model airplane plan

Gym Dandy

RC Modeler's Gym Dandy

INDOOR R/C flying has always been a tantalizing thought. You know - sitting in your living room, with a little six inch job buzzing around at your command. Maybe we'll see it one day - in fact, we probably will, in some modified form not in existence. Meanwhile, we have to settle for what is currently available. And it's not too bad, either.
Several years ago I published a design, called 'Warpy' (for obvious reasons) which was reasonably successful for that time. Since then, the .010 engine has been developed, transistorized receivers have improved, and most important, Hobby Poxy came into being.
Why is Hobby Poxy most important? Simply because the structure of an indoor model must be very light, and therefore fragile. This is no prob-lem with a rubber powered job, but glow fuel requires that the model cov-ering be fuel proof. If you use dope, it pulls the model all out of shape (that's how Warpy got its name), but with Hobby Poxy you can make the structure as light as the air loads will require, since the application of Hobby Poxy won't shrink the tissue and subsequently warp the structure.
Next, the .010 was a big step. The only problem is, it's too powerful, so you have to tame it down with an inefficient prop.
'Swamping' has been minimized by automatic volume control (AVC) circuits such as C&S's 'sensimatic' receivers. This is important in indoor flying because the model is frequently close to you, and swamping could cause it to 'zig' when you want it to 'zag!'
Finally, the small 'Minitron' compound escapement by O.S. eliminates the sequence operation required by the simple "bing-bang" escapement. My prototype of the design shown here has a Bonner SN, and I have to admit that too often I would "bing" when I should have "banged," so a "Minitron" com-pound escapement has been utilized to solve that problem.
Well, you still can't fly this design in your living room, but it's a real dandy for flying in a gymnasium - a Gym Dandy, in fact. So, build one up and get permission from the school principal to use the gym during some unscheduled periods.
Light weight is essential to keep the flying speed down - the prototype weighed in at four ounces! You should try to match this, because it gives a flying speed of about five to six miles per hour, and at that speed, even if the model hits anything, the only damage is to the model itself, which is easily repairable. The engine is a pylon mounted pusher configuration. Thus it won't be likely to get the prop entangled with any obstacles in case the model does hit something. The relatively high dihedral and huge rudder area makes it possible to rack the model around in tight circles without immediately spiralling down.
No landing gear is necessary. You hand launch, and with a little practice, you'll find you can fly it right to you and catch it in midair at the end of the flight.
The structure is a straightforward box, spar, and tissue framework just like old time rubber models. The tissue should be ironed before applying so that it's pretty smooth (let it cool an hour or so after ironing so it's at room temperature when you attach it to the framework).
The construction notes on the plans show all the required sizes of balsa; we don't have to go into it in any more detail, since it's self explanatory. Note the 'half size' pencells for receiver drain is small, and the O.S. escapement has a unique 'by-pass' feature that cuts the power requirement way down after the initial 'pull-in' power has been applied.
Perhaps your biggest problem will be matching the .010 power to your plane. To do this, you need a very inefficient prop - otherwise the Gym Dandy will beat itself to pieces on the ceiling!
I've shown a block from which you can carve a pusher prop, but you'll have to make a real 'club' blade in order to keep the thrust down. As a control device I've also shown a 'thrust reverser.' This is a little metal stub propeller with the blades twisted opposite to the main prop, thus counteracting the thrust. You can vary it by the amount of twist - even to the point of reducing the thrust to practically zero, even tho the engine is screaming. The amount of reverse thrust will depend on your particular plane, prop and engine combination. A couple of test flights will suffice for determining the necessary amount.
Even if you don't have a gym available, you can amaze your friends with this lumbering model by flying it outdoors on windless days. No matter where you fly it, you'll get a kick out of it. So build a Gym Dandy, just for the novelty. You'll be glad you did!

Link to this page: https://aerofred.com/details.php?image_id=97976

Sources: https://outerzone.co.uk/plan_details.asp?ID=7869
Details: Full Details
ID: 97976
File Size: 121.4 KB
Type: Airplane
Class: Radio-Control
Use: Sport
Motor: Glow-Powered
Motor Size:Less-Than-0.049-CI (2-strokes)
Wingspan: 37 in. / 94 cm
Publisher: RC Modeler
Magazines:  More at RCBookcase
Pub. Ref: Draw by Gerardo Flores
Designer: Ken Willard
Date: 12/1966
Weight Class:75g-To-100g (1.75oz-To-3.5oz)
Material:Various-Wood-Types
Listing Editor: André
Added: 13/01/2017 16:15
Updated: 10/01/19 11:45:51pm
Corrections? Contact André
Need Help? Forum
Filetype: .pdfSoftware for .pdf files

Member Profile for André

Hello!

I'm André Costa (Brazil), I build and fly model airplanes since
1968 (F/F, UC). At 1974 I ingressed in RC, my first radio, was a Logictrol 3 ch, the engine was OSmax 25 rc and Falcon 56.
In the 80's I build varied scale model airplanes. In 1985 I started the construction of a experimental ultra-light airplane in wood, which flew sucessfull in 1991. Currently, I dedicate to the research of inventive solutions for light electric models.
With my son Geraldo, I’m editing plan’s for you!
Best regard

Radio-Control Airplane Scale Outdoor Various-Wood-Types

Downloads
Download Main Plan file, possible versions and from alternative sources if available.

Order Prints


Plan details Prev Next Plan
These are the details for the "Gym Dandy" plan. If you would like to become a plan editor and help us to edit the attributes of all the plans in the website please click the "Edit Attributes" button below.

Plan Attributes: Edit Attributes
Plan ID:97976
Keywords:Indoor monochannel .010 stick construction vintage.
Class:Radio-Control
Model Type:Airplane
Channels:1-ch
Functions:Rudder
Aircraft Use:Sport
Wingspan: 37 in. / 94 cm
Wingspan Class:75cm-To-100cm (30in-To-40in)
Wing Position:High-Mounted-Wing
Wing Style:Straight-Wing-Rect
Wing Dihedral:Dihedral
Landing Gear:None
Motor Type:Glow-Powered
Motor Size:Less-Than-0.049-CI (2-strokes)
Number of Motors:1-Tractor
Weight Class:75g-To-100g (1.75oz-To-3.5oz)
Material:Various-Wood-Types
Construction Skills:Novice
Pilot Skills:Low-Intermediate
Publisher:RC Modeler
Magazines:  More at RCBookcase
Date:12/1966
Reference:Draw by Gerardo Flores
Designer:Ken Willard
Restorer:Not identified
Category:PDF Bitmap Wood Model Airplane Plans (2)
Similar:Plans like Gym Dandy
File Details:
Date:13/01/2017 16:15
Views:604
Downloads:71
Rating:1.00(1Votes)
File size:121.4 KB

Thinking about this one? Prev Next Plan
If you know about a building log for this plane please post a comment, we will add it to the listing here.

Order your Gym Dandy prints today!
The Gym Dandy plan can be printed on plain paper, tracing paper or polyester film and shipped worldwide.

Plans Service Calculator
Region:
Media:
Scale: The original wingspan for this model is 37 in. / 94 cm. Please Change the values below to order in a different wingspan.

Warning:
1. Scaling up a plan too much will degrade the line quality.
2. Please make sure the stated wingspan is correct.
Packaging:
Mail:

This calculator will work on pdf and image format files, if the file is very large, 5 or even 10 Mb it will take longer to process the plan file, it may finish even after the button animation stops spinning, please be patient when calculating larger files.

If second plan and up choose "2nd & Up" in the packaging option.

Ordering Prints
This tool allows you to calculate the cost of printing and shipping the Gym Dandy plans and its building article if available.

How to use
  1. Set the options on the left and click the Calculate button
  2. Change the options to match your needs, Polyester plans must me shipped rolled.
  3. When you're happy with the results click the Paypal Button and finish the checkout.
  4. I will review the order, print and ship within one business day.
Important!
  1. Make sure your Paypal address it´s correct.
  2. Make sure your Paypal email address it´s active, I will use it to communicate with you about the order and shipping. Or send me a message from the contact page so I can have your email address.
  3. Download and inspect the plan pdf file, the paper prints will be made from it.
Ordering several plans
  1. If one of the plans is Tracing paper or Polyester, select Cardboard Tube and all the other options and click "Add To Cart"
  2. Select "2nd & Up" as packaging
  3. Only need to add Tracking once.
  4. If there is any overcharge we will issue a refund after shipping via Paypal.
Requesting a Resized Plan
  1. If you need to resize a plan please contact us with the ID:97976 and the desired wingspan.
  2. We will send you a resized pdf for evaluation and upload the new file to the site so you can place the order.
Printing plans that are not on the site
  1. The best option is to get the plan pdf file, upload it here as a new listing and then use the calculator in it´s page..

Terms of Service.
Please read the Plans Printing Service Terms of Use before placing an order.

What are you ordering:

You are ordering a print from the main PDF file in this listing, it´s exactly like taking this file in a thumb drive to a local print shop and ask them to make a print.

About the plan source:

You should verify if the source file has the quality for the type of construction you intend to do, we will print the file without any kind of enhancement or scaling. To know if the file is good please download it and open it on a pdf viewer like Adobe pdf viewer and set the view level or zoom level to 100% or 1:1 or full scale or actual size, depending on which version or pdf viewer you are using. Also, using the measuring tool make sure all the parts fit together and have the correct size.
In doubt please ask us for an opinion.

Plans Scaling:

We can scale this plan for you. But please keep in mind that if this plan is not vector, if you enlarge it too much the quality will be degraded.

You will receive:

  • Laser Printed plan on good quality Bond paper or/and Tracing Paper and/or Polyester sheet of the PDF file from this listing, depending on what you have purchased.
  • Rolled sheets, up to 5 in the same cardboard tube.
  • Envelope, up to 5 sheets per envelope.
  • Articles and Instructions if they are available and if you order them.
  • Air Mail, Priority, Priority Insured or Normal mail, according to your choice.

About our printers:

We use professional quality laser OCÉ and Canon printers/copiers, these printers use toner, not ink so the printings will be durable and waterproof.

About the different media types:

Bond Paper: White Bond paper, 80 grams per square meter.
Bond Tracing paper: Bond Tracing paper, 90 grams per square meter.
Polyester film: High quality polyester sheet incredibly durable, will resist cuts and glue and can be washed (I use it as sail material on my RC sailboats).

Pricing:

We charge by print length (914mm or 91,4cm or 36in. by the length of the print)
This means that a plan 120cm by 150cm will be charged two times 150cm because it will be printed in two tiles, a plan 91cm by 150cm will be charged one time its length or 150cm and a plan 91cm by 40cm will be charged 40cm.
The system will try to fit a plan in the 91,4cm of the printer width in order to reduce the costs or print length to the maximum. This is the same charging method used in any printshop.

Packaging:

We will use paper or waxed paper padded envelopes for folded plans and hard cardboard tubes with plastic ends for rolled plans, depending on your choice.

Shipping:

We ship from Portugal, Europe and use the reliable Portuguese mail system CTT.
CTT has delivery agreements with different entities on each country so if you´re from the US you may have your order delivered by USPS, in the UK may be Royal Mail and so on.
Orders are dispatched on the next or second business day after purchase.

Postage:

We charge according to the ctt.pt postage table.

Mailing Methods:

Normal Mail: Normal Mail is non traceable, use at your own risk, no insurance, total loss if the carrier loses it.
Priority: Priority Mail is traceable on your local/national mail system, it is not insured.
Priority Insured: Priority Insured Mail is traceable on your local/national mail system and is insured.

Returns:

Please keep in mind that when you order a plan it will be printed specifically for you, just like when you go to a local print shop.
Before ordering please make sure that the plan will fit your needs, in doubt please ask us for an opinion. If you still receive a plan you don´t like we can accept it back if it is in good conditions but we will not refund the postage from the initial order, you will have to pay the postage to return the plan to us and a 30% re-stock fee will be applied so please, in doubt, please ask us for an opinion.

Payments:

Orders can be paid with Paypal or Credit Card via Paypal and are shipped to the address on your Paypal account or to the address you set at checkout.

About the Calculator:

The Plans Price Calculator will read the plan file and output all the information on the panel to the right according to the selected options, you can change the options and request a new quote at any time.
If you would like to print a plan that is not on the website you can upload it to the main plans category in pdf format, multiple sheets in the same pdf file, and use the Plans Price Calculator to get a quote and place the order.

3D Printed Parts
Order 3D Printed Parts for the Gym Dandy

General Information

3D printing allow us to design not only complete airplane models but also parts to complete balsa, foam or even composite model airplanes.

Parts can be designed and printed to fit exactly a model you have or a model you plan to build, even if you are not building this model to the full size plan.

3D Printing, and 3D CAD allow us to create the actual parts to fit on our models but also allow us to create negative molds where we can make composite parts.

I´m adding this service to all the plan listings on the site knowing that not every part you imagine or need can be done, knowing this, jobs will be evaluated case by case and a price estimate will be given on request.

What can be done with 3D Printing:

  • Canopies
  • Cowls
  • Wheel Pants
  • Landing Gears
  • Wing Ribs
  • Motor Mounts
  • Servo Trays
  • Servo Covers
  • Wings
  • Fuselages
  • Complete Models

Full Models, Wings or Fuselages

It is possible to design a complete model for you but keep in mind that this is a lengthy process, many hours are needed to design and test a fully 3D Printed model. The finished model cannot have the same internal structure of the wooden made counterpart because it wouldn´t be possible to print it, it would have to have a structure like the models you can see in the 3D Printed Kits section of the site.

From the outside they are very loyal to the plan but still they have to be printed in sections, typically to fit a 250X210X200 mm cube that is the printer maximum build volume.

3D Printed planes are also heavier than light balsa models, all built up and ready to fly, with an electric power system they are generally a little lighter than the same model if it were powered by a glow engine. Please have a look at the 3D Printed kits section to have an idea on this.

Pricing

I will calculate a price upon request, please contact me here mentioning this PlanID: 97976 and the job you wish me to do.

Comments
Questions or comments about the Gym Dandy? Your comments may help others to build this model...

Related Plans
Plans related to the main plan in this listing page.

NameSpanClassTypeUsePowerPublisherDesignerDate
Gym Dandy
ID:97107 | 393.6 KB
37 in. / 94 cm Radio-Control Glider Trainer Glow-Powered RCModeler Ken Willard 01/1966
GymDandy
ID:81673 | 212.5 KB
18 in. / 45.7 cm Free-Flight Airplane Xperimental Rubber-Band-Powered --- --- ---

3D Printed Kits
High Quality 3D Printed Kits in PLA, PET-G and ABS.

Zivko EDGE 540 Hannes Arch
46.5in./118cm Span

Zivko EDGE 540 Hannes Arch model airplane plan
Printed Kit in high quality PLA or PET.
Shipped in 3-4 business days. (PLA)

AICHI M6A Nanzan
42.1in./107cm Span

AICHI M6A Nanzan model airplane plan
Printed Kit in high quality PLA or PET.
Shipped in 3-4 business days. (PLA)

Das Liddle Stik
45.7in./116cm Span

Das Liddle Stik model airplane plan
Printed Kit in high quality PLA or PET.
Shipped in 3-4 business days. (PLA)

Free Plans
Download Free Model Plans.

Senior Aero Sport
Radio-Control / Civilian / 67 in. / 170.2 cm Span
Senior Aero Sport model airplane plan
 461
Radio-Control
Airplane
Glow-Powered
Nova
Radio-Control / Sport / 45.7 in. / 116.1 cm Span
Nova model airplane plan
 331
Radio-Control
Airplane
Glow-Powered
Das Box Fly 10MG
Radio-Control / Sport / 60 in. / 152.4 cm Span
Das Box Fly 10MG model airplane plan
 276
Radio-Control
Airplane
Glow-Powered
Jetstream A1 Ambroid
Free-Flight / Thermal / 47 in. / 119.4 cm Span
Jetstream A1 Ambroid model airplane plan
 47
Free-Flight
Glider
Not-Powered
Vintage Magazines by Hlsat
Share Your Plans With Us

AeroFred.com is a Plans Sharing Community, not just a website to grab some plans.

Every day thousands of modelers visit us and download free model airplane and boat plans, plans shared by other modelers...

If you have plans that are not here please upload them, so others can build from them.


Upload a Plan

Please login first

Details | Gallery | Prints