Home 3D Printed Model Airplanes 3DLabPrint Zivko EDGE Hannes Arch

Zivko EDGE Hannes Arch ( 46.5 in. / 118 cm )64.00 Eur.


The Zivko EDGE Hannes Arch
We are proud to present the latest in Model Airplanes building technology, 3DLabPrint's creations. We will print on demand a high quality print of the Zivko EDGE Hannes Arch for you.

Zivko EDGE Hannes Arch model airplane plan

Zivko EDGE Hannes Arch
Order the Zivko EDGE Hannes Arch Kit

Zivko EDGE Hannes Arch High quality 3D Printed Kit
Printed Model Airplanes FAQ


3D Printed Kit on PLA Zivko EDGE Hannes Arch.

This is a great scale model of the famous Zivko Edge. This model is very well designed and flies well. Thanks to its large control surfaces it can deliver fast manoeuvres and at the same time be very controllable.

It requires 4 sevos and a 40 amps esc.

Two landing gears are included, one in PLA in the same colour of the rest of the plane and one in PET-G in grey. PET-G is extremely resistant. It is not necessary to flue the landing gear, it will slide in and become secure to the fuselage fixing holes so you can always swap it.

Replying to one of the comments:

The PLA I use on these models (as of 6/2017) is rated with nearly the same heat resistance and tensile strength as ABS, it will hold up to 85C. So it will resist the hear from the motor and battery pack.

The motor is fixed from behind and the front of the plane is wide open and it also has side vents, plenty of cooling under normal circumstances.

Specs:
Lenght: 1048mm (41.0in)
Wingspan: 1187mm (46.7.1in)
Height: 368mm (14.5in)
Wing area: 23.0 dm2
Wing loading: 48.6 g/dm2
Airfoil: NACA sym. modificated

Print weight: 730g
Empty weight (w/o battery): 910g
Takeoff weight (6s 1300 lipo): 1120g
Max takeoff weight: 1300g
Never exceed speed, VNE: 205 km/h
Design maneuvering speed, VA: 165km/h
Stall speed, VS: 30 km/h

HIGH PERFORMANCE SETUP:
See video guide #6 (for HP setup)
Motor – AX-4008Q-620KV
Speed controler (ESC) – CC Talon 25 or similar 30-40A/6s
Battery 1300mAh/6s up to 2200/6s or 2x 1300-2200/3s

ECO PERFORMANCE SETUP:
Turnigy D3530/14 1100KV or similar 3530-35 1100kv
40A Electronic Speed Controller or similar 40Amps
Turnigy 2700mAh 3S 20C or similar 2200-3800/3s


Available Files

Here you can find the manual for the Zivko EDGE Hannes Arch.

Download Manual


Filaments used

We use the so-called High-Temp PLA that is in fact Ingeo 3d850 polymer made in the USA and extruded in Europe and we are in the process of changing all production to the new Ingeo 3d870 polymer that has an impact resistance comparable to ABS. Currently only white prints will be done with the 3d870 filament and as our suppliers start producing filament in other colors we will replace one for the other.

Both are excellent products just the Ingeo 3d870 is better.

PET-G parts are printed with Devil Design PET-G or some other good quality I have here. I don´t know who is exactly the manufacturer of the polymer, its not always easy to know that.


Recommended CA Glue

Glue:
HK Medium thickness CA

Accelerator:
HK Accelerator

Note:
This glue and accelerator have been tested and work on PLA, not all glues and accelerators, specially the accelerators work well. If you purchase the Zivko EDGE Hannes Arch Kit I will include a piece of printed PLA so you can do your tests.


Recommended Power Sets

You can find links to the power sets components in the user manual.
Download Manual


Hot weather

In the Summer it's advisable to not let a printed plane inside the car under the sun, it will become deformed like any other plane made of plastic. At the flying field, planes made or painted with dark colors can become hot and can become deformed, leave your printed plane in the shade.


Building Log

3DLabPrint has created the following Zivko EDGE Hannes Arch building log.
Zivko EDGE Hannes Arch Building Log


More Videos

3DLabPrint has uploaded the following Zivko EDGE Hannes Arch to their Youtube Channel.
Zivko EDGE Hannes Arch Videos

Details: Full Details
ID: 99259
Type: Airplane
Class: Radio-Control
Use: Acro
Motor: Electric-Powered
Motor Size:500-To-750-Watt 
Wingspan: 46.5 in. / 118 cm
Publisher: 3DLabPrint
Designer: 3DLabPrint
Weight:1120 g
Material:Plastic-PLA

About 3D Printed Model Airplanes
If you have doubts about how these models are designed, printed and how the fly, this page is for you.

Before anything else, watch this video.

The most common question I get is:

-How do these planes fly?

The video at the right is from FliteTest's Youtube channel, they installed cameras on the plane and filmed it in flight with a drone, these images are not only spectacular but they also allow us to see the behavior of the plane in flight. Enjoy!

This P-38 in the video requires:

  • 12 channels radio if you don´t use y-cables.
  • 4-5 full days straight to print on one printer if everything goes well.

All our 3D Printed planes are here.


About 3DLabPrint models

These models are designed by Stepen in the Czech Republic, are easy and quick to build and have excellent flight characteristics. The gear is pretty standard, usually 9 or 12 grams servos and two power setups are usually suggested, one composed of high quality motor, ESC and battery and another made from inexpensive HobbyKing stuff but still very capable and with good performance.

When you build from a plan or when you assemble a wood kit, usually you add parts to a developing structure, you may have the fuselage done then you may add a servo tray then you may add a motor mount and so on, on these printed planes everything is built with full integration in mind, all the internal reinforcements, all the linkages, all the ducts for wiring, all the fixtures are one with the structure, in fact, many times you have ducts for the servo wires acting as an internal wing reinforcement.

This is a revolutionary way of thinking or better, a revolutionary way of fabricating model airplanes because many of us had already thought about how good this kind of approach could be but actually doing it has always been the problem.

Even with the advent of high quality/low cost 3D printers this has not became immediately possible, it took a very gifted person, Stepen, to create a design method and correspondent print setting to make these marvelous models possible.

I hope you are not afraid to try the latest in model airplane construction, I´m sure you will be delighted with these amazing model airplanes.

A FAQ page with answers to the most common questions can be found here.

All questions are welcome. Please contact us here.


3D Printed Planes Gallery
These are just a few examples of the amazing internal structures you will find on a 3D printed model airplane.

Order 3D Printed Zivko EDGE Hannes Arch
Please select the options below.

Order the Zivko EDGE Hannes Arch kit or partsFAQ
Region:
Complete Kit:
Complete KIT.
Spare Parts and Options:
All the components can be printed on demand.
Printed Manual:
Free but adds 100 grams of weight!
Download Manual
Color:




** Other colors may delay the delivery and production of your kit for 2-3 days. After purchase I will contact you to define how the colors will be used.
PLA can be painted with acrylic spray.
The production lead time for new orders is currently 2 days or less.

Ordering a 3D Printed "Zivko EDGE Hannes Arch"" Kit
This tool allows you to calculate the cost of printing and shipping the Zivko EDGE Hannes Arch model airplane kit and/or spare parts.

How to order:
  1. Set the options on the left and click the "Calculate" button
  2. Change the options as needed and click "Calculate" button again.
  3. When you're happy with the results click the Paypal Button and finish the checkout at Paypal´s website.
  4. I will review the order, print and ship.
  5. Printing the Zivko EDGE Hannes Arch takes approximately 48 hours on one single printer, thankfully we have more than one printer so your kit will be produced just in 8 to 36 hours, depending on the complexity of the print.
Packaging & Postage:
  1. Larger parts individually bagged then everything in one larger bag so nothing gets lost or damaged.
  2. Single or double cardboard box with bubble wrap cushioning.
  3. Shipped by Registered Airmail with Tracking Code.
Note:
  1. The PDF Assembly manual has links to web pages where you can obtain the needed electronics and even some supplies.
  2. On multiple kits orders, each kit will be shipped on an individual box, it wouldn't be cheaper to ship combined.

Terms of Service.
Please read the 3D Printing Service Terms of Use before placing an order.

About the 3D File source:

The Zivko EDGE Hannes Arch was designed by 3DLabPrint and will be printed by AeroFred as a service.

Model Printing and Order Processing:

Printing a model airplane requires many hours of printing, typically, for the models we sell, between 24 and 72 hours if the job is done one one single printer. Luckily we have many printers so your new plane will be ready to ship in 1-2 days or even less if it´s a small model.

Scaling:

Models from 3DLabPrint can´t be scaled because we don´t have access to the original 3D CAD files to do a proper scaling. When these models are printed all the needed fixtures for motor, battery pack, servos, links, wiring ducts are also printed so they would all be scaled making them impossible to use.

Modifications:

The models from 3DLabPrint are supplied as print files only, we don´t have access to original 3D CAD files so I can´t do modifications. However, PLA glues very well with CA and accelerator so you can do as in any other model airplane kit, you can add balsa or lite ply and you can make any modifications yourself.

You will receive:

  • Complete Zivko EDGE Hannes Arch 3D Printed KIT on PLA or individual parts for the same model, depending on your order.
  • One piece of printed PLA, some bad print I may have around here, so you can do your experiments and tests instead of trying on the plane itself.
  • Cardboard box with appropriate cushioning so the parts are protected during the shipment.
  • Assembly manual printed copy from 3DLabPrint if requested at the ordering page.

The paper manual is free but not included by default because it adds weight that may make the postage costs climb considerably. I reserve the right to add the paper manual or not.
In any case the manual can be downloaded in PDF format in this same page and it will have links to web pages where some of the needed parts an be ordered.


You will NOT receive:

  • 3d .stl or .gcode files, project files or any files at all apart from the pdf manual.
  • CA Glue or CA Accelerator.
  • Electronic components.
  • Wheels, hinges, propellers, screws, piano wire, paint or decals.

Note:
Vinyl decals do not stick on 3d printed planes, the only way to add insignia, camouflage, letterings is to paint with acrylic spray paint and a stencil or a mask.


Assembly and preparation:

Modeling work it´s your job :)
You will have to follow the manual to assembly this kit and do all the work needed, this is a model airplane Kit, not a toy.

About our printers:

We use high quality original 3D Printers, no Chinese clone printers or cheap Ebay 3d printers.

About the different filament types:

PLA (Polylactic Acid): Most common and easy to use bioplastic, have a read.
ABS (Acrylonitrile butadiene styrene): Good for parts requiring higher temperature operation, have a read.
PETG (Polyethylene terephthalate): Used when high mechanical strength is required, have a read..

Packaging:

We will use strong cardboard boxes and the appropriate cushioning to protect the printed parts.

Shipping:

We ship from Portugal, Europe and use the reliable Portuguese mail system CTT.
CTT has delivery agreements with different entities on each country so if you´re from the US you may have your order delivered by USPS, in the UK may be Royal Mail and so on.


Postage:

We charge according to the ctt.pt postage table.

Tracking:

All 3D Printed models and parts are shipped registered. A signature will be required at the delivery address, not necessarily yours but someone at the address.

Returns:

We will only accept returns of non assembled, undamaged complete models or spare parts.
Postage fees from the original order are non refundable and you will have to pay the postage back to us.
No re-stocking fee if everything arrives in good condition.
In doubt please ask us for an opinion.

Payments:

Orders can be paid with Paypal or Credit Card via Paypal and are shipped to the address on your Paypal account or to the address you set at checkout.

Spare Parts and Options
All the individual sections of the Zivko EDGE Hannes Arch can be re-printed on demand.

Zivko EDGE Hannes Arch (3d Printed Kit)

Fully Printed Zivko EDGE Hannes Arch Kit

Price: 64Eur.

Wing Section

1 wing panel for this model

Price: 4Eur.

Fuselage Section

1 fuselage section for this model

Price: 4Eur.

Tail Parts

Horizontal, vertical stabilisers and control surfaces

Price: 2Eur.

PET-G Landing Gear

Main Landing Gear printed on grey PET-G

Price:  Eur.

Details
These are the details for the "Zivko EDGE Hannes Arch" model.

Plan Attributes: Edit Attributes
Plan ID:99259
Keywords:Zivko EDGE Hannes Arch
Class:Radio-Control
Model Type:Airplane
Channels:4-ch
Functions:Ailerons-Elevator-Rudder-Throttle
Aircraft Use:Acro
Wingspan: 46.5 in. / 118 cm
Wingspan Class:100cm-To-125cm (40in-To-50in)
Wing Position:Mid-Mounted-Wing
Wing Style:Straight-Wing-Trap
Wing Dihedral:Dihedral
Landing Gear:Taildragger
Motor Type:Electric-Powered
Motor Size:500-To-750-Watt 
Number of Motors:1-Tractor
Weight:1120 g
Material:Plastic-PLA
Construction Skills:Low-Intermediate
Pilot Skills:High-Intermediate
Publisher:3DLabPrint
Date:06/2016
Reference:02
Designer:3DLabPrint
Found:
Listing Editor:3DLabPrint
Category:3DLabPrint
Similar:Plans like Zivko EDGE Hannes Arch

Video
Videos for the Zivko EDGE Hannes Arch.


Building Log

3DLabPrint has created the following Zivko EDGE Hannes Arch building log.
Zivko EDGE Hannes Arch Building Log


All the Zivko EDGE Hannes Arch Videos

3DLabPrint has uploaded the following Zivko EDGE Hannes Arch to their Youtube Channel.
Go to Zivko EDGE Hannes Arch Videos

Thinking about building the Zivko EDGE Hannes Arch? Prev Next Plan
If you know about a building log for this plane please post a comment, we will add it to the listing here.


Video Guide

3DLabPrint has created the following Zivko EDGE Hannes Arch video guide:
Zivko EDGE Hannes Arch Video Guide

Comments
Questions or comments about the Zivko EDGE Hannes Arch? Your comments may help others to build this model...

High Performance Engine Bdunz on 21/04/2017 15:44
The motor listed for the High Performance Setup is AX-4008Q-620KV. I find an AX-4008Q-600KV quadcopter motor at Hobby King and the same motor is referenced several times in google, but nothing (out-runner, etc. ) that matches the description and there is nothing in the manual to give me a clue. What motor is recommended?
Zivko EDGE Hannes Arch derfred on 22/04/2017 10:57
Hello Barry,

The suggested high performance motor is this one:
https://hobbyking.com/en_us/ax-4008q-620kv-brushless-quadcopter-motor.html?___store=en_us

This is the motor listed in the "High performance setup" in the manual.

It is an out-runner and can be used on a quadcopter or on a plane. An out runner is nothing but a motor on which the outer can with the magnets rotate and the coil is fixed, an in runner is the opposite, the magnets are fixed and the coil rotates with the shaft.

As ESC I would suggest this one:
https://hobbyking.com/en_us/turnigy-plush-40amp-speed-controller-w-5a-bec.html
or
https://hobbyking.com/en_us/hobbyking-40a-blueseries-brushless-speed-controller.html
3D Flying possibilities Wingzar on 24/05/2017 08:00
Hello !
I am really interested in the plane but I haven't been able to figure out if this little can do 3D. Is it capable of 3D flying ?
I also would be curious to know what is the advantage of using a high voltage like 6S compared to a standard 3/4S that is often used for this size of planes.

Thanks in advance for you answers !
Zivko EDGE Hannes Arch derfred on 26/05/2017 09:37
Hello Wingzar,

This is not a 3D plane, the control surfaces are large but not as large on a 3D plane. I would say it falls between a sport plane and a 3D.

The advantage of using the quadcopter motor... Well, I guess the only advantage would be if the designer had many of these laying around :) I would put a power setup as you say, 2200 mA/h 3 or 4 S at the most and a 35 mm can motor, the length of the can could be around 36mm so a C3536 instead of the eco setup you see in the description and around 1000 KV possibly 1200 KV and you would have a pretty powerful setup for a plane this size.

Kind regards,
Fred
What will I get netsnake on 24/06/2017 05:56
I coudnt figure out if the price is for the real parts or for the printdata only.
What size of print area is needed ?
Does the PLA material resist the heat of the motor or akku ?

great work
Zivko EDGE Hannes Arch derfred on 02/07/2017 17:35
The price is for a KIT (a real plane printed on PLA in the chosen colour)

The PLA I use on these models (as of 6/2017) is rated with nearly the same heat resistance and tensile strength as ABS, it will hold up to 85C. So it will resist the hear from the motor and battery pack.

In this model the motor is fixed from behind and the front of the plane is wide open and it also has side vents, plenty of cooling under normal circumstances.

P47 N-15 THUNDERBOLT model airplane plan
 254
Radio-Control
Airplane
Electric-Powered
Fighter
Mig-15 model airplane plan
 490
Radio-Control
Airplane
Electric-Powered
Fighter
P51-D MUSTANG model airplane plan
 407
Radio-Control
Airplane
Electric-Powered
Fighter
P-38 LIGHTNING model airplane plan
 761
Radio-Control
Airplane
Electric-Powered
Fighter
Spitfire MK IX model airplane plan
 256
Radio-Control
Airplane
Electric-Powered
Fighter
Details | Gallery | Article | Supplemental |