Home 3D Printed Model Airplanes 3DLabPrint Zivko EDGE Hannes Arch (Scaled up)

Zivko EDGE Hannes Arch (Scaled up) ( 61.4 in. / 156 cm )99.00 Eur.


The Zivko EDGE Hannes Arch (Scaled up)
We are proud to present the latest in Model Airplanes building technology, 3DLabPrint's creations. We will print on demand a high quality print of the Zivko EDGE Hannes Arch (Scaled up) for you.

Zivko EDGE Hannes Arch (Scaled up) model airplane plan

Zivko EDGE Hannes Arch (Scaled up)
Order the Zivko EDGE Hannes Arch (Scaled up) Kit

Zivko EDGE Hannes Arch (Scaled up) High quality 3D Printed Kit
Printed Model Airplanes FAQ


Same as:
https://aerofred.com/details.php?image_id=99259

But with 156cm wing span and printed with interleaved 1 wall 2 walls skin for more rigidity.

The wing is printed with two walls in the first 10cm then several profiles with 2 walls were added at key spots to maintain the airfoil shape and structural rigidity.

The fuselage has 1cm wide two walls bands repeated each 4cm and the front section has two walls from the tip to the end of the motor mount there are a few more bands in some key areas, on the last section its the same but with wider bands to hold the horizontal and vertical stabilisers.

Ailerons, horizontal and vertical stabilisers and control surfaces all have the 1cm/4cm pattern, the some as the fuselage.
The outer surface is smooth, the double walls are only noticeable from the inside.

###

Wingspan: 1560mm
Print Weight: +/-1750grams
AUW: +/- 2950grams
Power: +/- 2000 watts

###

Issues related to the enlargement:

Not many, the servos were 5 grams, now 11 grams (Hitec HS-81 or HS-82 type) servos will fit perfectly, tightly, the landing gear will work perfectly well but wheels rims may need to be drilled to fit the supplied axles or a piece of plastic tube, carbon fibre tube, a piece of threaded rod can be used instead of the supplied wheels axles.

From the feedback I´ve received the supplied motor mount has worked perfectly without any need for adapting plates.

###

Tested with this gear by our friend Hans-Peter from Switzerland:

Dualsky XM 5050EA-08 ( 290grams, 525 KV and 50.5mm in length ) driving a RFM 16x13 folding prop on a 65mm HM centerpiece and a 60mm HM spinner ( this means actual prop dia is 16.9” )

On 5s , it will produce some 1800 watts – just perfect ! This motor fits perfectly with the standard plug in mount and giving me some 3mm gap between spinner and fuse front ring

I do estimate the all up weight to be around 2950 gramms – very nice !

Hitech HS 82MG servos fit perfectly into the slots of the fuse and the wings ! ( they have 3.4kg of torque on 6volts – perfect match again ! )

Hans-Peter´s plane flies like a dream :)

###

The main picture in the listing is from the normal 100% scale plane, the other pictures are from the 130% scaled plane.


Available Files

Here you can find the manual for the Zivko EDGE Hannes Arch (Scaled up).

Download Manual


Recommended CA Glue

Glue:
HK Medium thickness CA

Accelerator:
HK Accelerator

Note:
This glue and accelerator have been tested and work on PLA, not all glues and accelerators, specially the accelerators work well. If you purchase the Zivko EDGE Hannes Arch (Scaled up) Kit I will include a piece of printed PLA so you can do your tests.


Recommended Power Sets

You can find links to the power sets components in the user manual.
Download Manual


Hot weather

In the Summer it's advisable to not let a printed plane inside the car under the sun, it will become deformed like any other plane made of plastic. At the flying field, planes made or painted with dark colors can become hot and can become deformed, leave your printed plane in the shade.


More Videos

3DLabPrint has uploaded the following Zivko EDGE Hannes Arch (Scaled up) to their Youtube Channel.
Zivko EDGE Hannes Arch (Scaled up) Videos

Details: Full Details
ID: 99638
Type: Airplane
Class: Radio-Control
Use: Sport
Motor: Electric-Powered
Motor Size:1200-To-2200-Watt 
Wingspan: 61.4 in. / 156 cm
Publisher: 3dLabPrint
Designer: 3dlabprint
Weight:2950 g
Material:Plastic-PLA

About 3D Printed Model Airplanes
If you have doubts about how these models are designed, printed and how the fly, this page is for you.

Before anything else, watch this video.

The most common question I get is:

-How do these planes fly?

The video at the right is from FliteTest's Youtube channel, they installed cameras on the plane and filmed it in flight with a drone, these images are not only spectacular but they also allow us to see the behavior of the plane in flight. Enjoy!

This P-38 in the video requires:

  • 12 channels radio if you don´t use y-cables.
  • 4-5 full days straight to print on one printer if everything goes well.

All our 3D Printed planes are here.


About 3DLabPrint models

These models are designed by Stepen in the Czech Republic, are easy and quick to build and have excellent flight characteristics. The gear is pretty standard, usually 9 or 12 grams servos and two power setups are usually suggested, one composed of high quality motor, ESC and battery and another made from inexpensive HobbyKing stuff but still very capable and with good performance.

When you build from a plan or when you assemble a wood kit, usually you add parts to a developing structure, you may have the fuselage done then you may add a servo tray then you may add a motor mount and so on, on these printed planes everything is built with full integration in mind, all the internal reinforcements, all the linkages, all the ducts for wiring, all the fixtures are one with the structure, in fact, many times you have ducts for the servo wires acting as an internal wing reinforcement.

This is a revolutionary way of thinking or better, a revolutionary way of fabricating model airplanes because many of us had already thought about how good this kind of approach could be but actually doing it has always been the problem.

Even with the advent of high quality/low cost 3D printers this has not became immediately possible, it took a very gifted person, Stepen, to create a design method and correspondent print setting to make these marvelous models possible.

I hope you are not afraid to try the latest in model airplane construction, I´m sure you will be delighted with these amazing model airplanes.

A FAQ page with answers to the most common questions can be found here.

All questions are welcome. Please contact us here.


3D Printed Planes Gallery
These are just a few examples of the amazing internal structures you will find on a 3D printed model airplane.

Order 3D Printed Zivko EDGE Hannes Arch (Scaled up)
Please select the options below.

Order the Zivko EDGE Hannes Arch (Scaled up) kit or partsFAQ
Region:
Complete Kit:
Complete KIT.
Color:




** After purchase I will contact you to define how the colors will be used, please keep an eye on your SPAM folder too.
Important! Please read.
  1. Make sure your Paypal address it´s correct.
  2. Make sure your Paypal email address it´s active, I will use it to communicate with you about the order and shipping. Or send me a message from the contact page so I can have your email address.

Ordering a 3D Printed "Zivko EDGE Hannes Arch (Scaled up)"" Kit
This tool allows you to calculate the cost of printing and shipping the Zivko EDGE Hannes Arch (Scaled up) model airplane kit and/or spare parts.

How to order:
  1. Set the options on the left and click the "Calculate" button
  2. Change the options as needed and click "Calculate" button again.
  3. When you're happy with the results click the Paypal Button and finish the checkout at Paypal´s website.
  4. I will review the order, print and ship.
  5. Please keep an eye on your email inbox and SPAM folders.
  6. Printing the Zivko EDGE Hannes Arch (Scaled up) takes approximately 72 hours on one single printer, thankfully we have more than one printer so your kit will be produced just in just a fraction of that.
Packaging & Postage:
  1. Larger parts individually packed in bubble wrap film so nothing gets lost or damaged.
  2. Double cardboard box.
  3. Registered Airmail. The tracking number will be sent to you and posted at Paypal´s website
Note:
  1. The PDF Assembly manual has links to web pages where you can obtain the needed electronics and even some supplies.
  2. On multiple kits orders, each kit will be shipped on an individual box, it wouldn't be cheaper to ship combined.

Terms of Service.
Please read the 3D Printing Service Terms of Use before placing an order.

About the 3D File source:

The Zivko EDGE Hannes Arch (Scaled up) was designed by 3DLabPrint and will be printed by AeroFred as a service.

Model Printing and Order Processing:

Printing a model airplane requires many hours of printing, typically, for the models we sell, between 24 and 280 hours if the job is done one one single printer. Luckily we have many printers so your new plane will be ready to ship in 1-2 days.

Scaling:

Models from 3DLabPrint can be scaled up by up to 130% depending on the model but please know that when these models are printed all the needed fixtures for motor, battery pack, servos, links, wiring ducts are also printed so they would all be scaled so additional work will be required on your end to fit the gear.
As an example, the Edge uses 5 grams servos, if scaled to 130% (1,56m) the servo slots will hold 12 grams servos perfectly but the motor mount will have to be adapted. This can be easily done by using bolts from end to end and washers in the back. Not beg deal. But on the P-47 that uses retracts the ob is not this easy, you would have to create a plate with holes to secure the retracts to the wing.

Modifications:

We can´t do modifications at design level. However, PLA glues very well with CA and accelerator so you can do as in any other model airplane kit, you can add balsa or lite ply and you can make any modifications yourself.

You will receive:

  • Complete Zivko EDGE Hannes Arch (Scaled up) 3D Printed KIT on PLA or individual parts for the same model, depending on your order.
  • One piece of printed PLA, some bad print I may have around here, so you can do your experiments and tests instead of trying on the plane itself.
  • Cardboard box with appropriate cushioning so the parts are protected during the shipment.
  • Assembly manual printed copy from 3DLabPrint if requested at the ordering page.

The paper manual is free but not included by default because it adds weight that may make the postage costs climb considerably. I reserve the right to add the paper manual or not.
In any case the manual can be downloaded in PDF format in this same page and it will have links to web pages where some of the needed parts an be ordered.


You will NOT receive:

  • 3d .stl or .gcode files, project files or any files at all apart from the pdf manual.
  • CA Glue or CA Accelerator.
  • Electronic components.
  • Wheels, hinges, propellers, screws, piano wire, paint or decals.

Note:
Vinyl decals do not stick on 3d printed planes, the only way to add insignia, camouflage, letterings is to paint with acrylic spray paint and a stencil or a mask.


Assembly and preparation:

Modeling work it´s your job :)
You will have to follow the manual to assembly this kit and do all the work needed, this is a model airplane Kit, not a toy.

About our printers:

We use high quality original 3D Printers, no Chinese clone printers or cheap Ebay 3d printers.

About the different filament types:

PLA: PLA is the most used material on 3d printing today, it prints well, with good finishing and little or no warping.
ABS: ABS is one of the most commonly used plastic, Legos are ABS, your car bumpers are probably ABS. This material has a high resistance to heat and it´s strong. It would be perfect for our planes if it wasn´t so hard to print.
PET-G: PET-G is the material used on plastic bottles, it´s very strong and has a heat resistance close to ABS, the only drawback is it´s flexibility. PET-G it´s a little more flexible than PLA but still can be used for printed planes.

As you see no material is perfect, I could continue describing other materials such as nylon, carbon impregnated PLA and so on and we would always find positive and negative aspects for each one of them.
Solution, we use PLA, namely NatureWorks 3d850 or 870 PLA that is one of the best, if not the best PLA in production today and for landing gears, motor mounts and other parts that require higher temperature tolerance and/or mechanical resistance we use ABS or PET-G.

Packaging:

We will use strong double wall cardboard boxes and the appropriate cushioning to protect each one of the printed parts, every part is rolled on bubble wrap plastic film.

Shipping:

We ship from Portugal, Europe and use the reliable Portuguese mail system CTT.
CTT has delivery agreements with different entities on each country so if you´re from the US you may have your order delivered by USPS, in the UK may be Royal Mail and so on.


Postage:

We charge according to the ctt.pt postage table. The smaller planes that fit boxes up to 90cm (sum of the three dimensions) we ship as a "letter" so the postage it´s cheap, larger planes have to be shipped as a package, there is no way around it and this is why the postage it´s expensive.

Tracking:

All 3D Printed models and parts are shipped registered. A signature will be required at the delivery address, not necessarily yours but someone at the address.

Returns:

We will only accept returns of non assembled, undamaged complete models or spare parts.
Postage fees from the original order are non refundable and you will have to pay the postage back to us.
No re-stocking fee if everything arrives in good condition.
In doubt please ask us for an opinion.

Payments:

Orders can be paid with Paypal or Credit Card via Paypal and are shipped to the address on your Paypal account or to the address you set at checkout.

ToS Acknowledgment:

Placing an order on this page implies acceptance of the above Terms of Service.

Spare Parts and Options
All the individual sections of the Zivko EDGE Hannes Arch (Scaled up) can be re-printed on demand.

Zivko Edge (156cm)

Scaled up Edge 156cm span

Price: 99Eur.

Details
These are the details for the "Zivko EDGE Hannes Arch (Scaled up)" model.

Plan Attributes: Edit Attributes
Plan ID:99638
Class:Radio-Control
Model Type:Airplane
Channels:4-ch
Functions:Ailerons-Elevator-Rudder-Throttle
Aircraft Use:Sport
Wingspan: 61.4 in. / 156 cm
Wingspan Class:125cm-To-160cm (50in-To-63in)
Wing Position:Mid-Mounted-Wing
Wing Style:Straight-Wing-Trap
Wing Dihedral:Dihedral
Landing Gear:Taildragger
Motor Type:Electric-Powered
Motor Size:1200-To-2200-Watt 
Weight:2950 g
Weight Class:2000g-To-2500g (70.5oz-To-88.1oz)
Material:Plastic-PLA
Construction Skills:Low-Intermediate
Pilot Skills:Low-Intermediate
Publisher:3dLabPrint
Date:06/2016
Designer:3dlabprint
Found:
Submitted to AeroFred.com
Listing Editor:3DLabPrint
Category:3DLabPrint
Similar:Plans like Zivko EDGE Hannes Arch (Scaled up)

Video
Videos for the Zivko EDGE Hannes Arch (Scaled up).


All the Zivko EDGE Hannes Arch (Scaled up) Videos

3DLabPrint has uploaded the following Zivko EDGE Hannes Arch (Scaled up) to their Youtube Channel.
Go to Zivko EDGE Hannes Arch (Scaled up) Videos

Thinking about building the Zivko EDGE Hannes Arch (Scaled up)? Prev Next Plan
If you know about a building log for this plane please post a comment, we will add it to the listing here.

Comments
Questions or comments about the Zivko EDGE Hannes Arch (Scaled up)? Your comments may help others to build this model...


Related Plans
Plans related to the main plan in this listing page.

NameSpanClassTypeUsePowerPublisherDesignerDate
Zivko EDGE Hannes Arch
ID:99259 | 478.5 KB
46.5 in. / 118 cm Radio-Control Airplane Acro Electric-Powered 3DLabPrint 3DLabPrint 06/2016
P51-D MUSTANG model airplane plan
 483
Radio-Control
Airplane
Electric-Powered
Fighter
Mig-15 model airplane plan
 623
Radio-Control
Airplane
Electric-Powered
Fighter
P47 N-15 THUNDERBOLT model airplane plan
 314
Radio-Control
Airplane
Electric-Powered
Fighter
MESSERSCHMITT BF 109T model airplane plan
 425
Radio-Control
Airplane
Electric-Powered
Fighter
Zivko EDGE Hannes Arch model airplane plan
 783
Radio-Control
Airplane
Electric-Powered
Acro
Details | Gallery | Supplemental |